A-Plus® Quick Drying Enamel Paint 4L

is a A-Plus® Quick Drying Enamel premium solvent-based Alkyd Enamel paint suitable for a wide range of wooden and metal surfaces. It cures to a tough, durable, high build glossy coating with superior hiding power, resulting to a long-lasting beautiful finish. It is Lead-free which makes it safe for painting household surfaces.

☑Premium Alkyd Enamel-Based Paint

☑Suitable for Interior and Exterior Use

☑Glossy and High Build Coating

☑Superior Durability and Adhesion

☑Excellent Resistance to Chemicals, and Oils

☑Protection Against Abrasion and Rusting

☑Easy to Use, Lead-Free

☑Available in 15 Factory-Mixed Colors

Category: Decorative PaintsTag: Alkyd Enamel / Oil Based Coatings

Painting Procedure on Wooden Substrates:

1. Primer: Apply at least 2 coats of A-Plus® Flatwall Enamel White as primer.
2. Putty: Repair cracks and other surface imperfections with A-Plus® Fast-Drying Plastic Wood Filler or  A-Plus® Enamel Glazing Putty White.
3. Topcoat: Apply 2-3 coats of your choice color of A-Plus® Quick Drying Enamel Paint. Allow at least 6-8 hours drying time between each coat.

Painting Procedure on Metal Substrates:

1. If previously painted, strip off all loose and chalking paint. If rust is present, apply A-Plus® Rust Converter first. Sand with large grit sandpaper to roughen surface.
2. Primer: Un-Galvanized or rusted metal substrates should be pre-painted with at least 2 coats of a premium quality anti-corrosive metal primer such as A-Plus® Metal Primer Red Oxide or Glazer Galva-Plus® Epoxy Primer.
3. Topcoat: Apply 2-3 coats of your choice color of A-Plus® Quick Drying Enamel Paint. Allow at least 6-8 hours drying time between each coat.

General Instructions:

1. Surface to be painted must be thoroughly cleaned, free of any contaminants.
2. For bare surfaces, sand with large grit sandpaper to enhance paint adhesion.
3. If previously painted, strip off all loose and chalking paint with A-Plus Supertanggal® Paint Remover.
4. Mix well before using.

For Wooden Surfaces:

1. Surface to be painted must be thoroughly cleaned, free of any contaminants.
2. Hammer nail holes and sand any surface defects with large grit sandpaper.
3. Repair cracks and other surface imperfections with A-Plus® Fast-Drying Plastic Wood Filler or A-Plus® Enamel Glazing Putty White.
4. Avoid painting under extreme environmental conditions and/or bad weather conditions.

For Metal Surfaces:

1. Remove dust, dirt, grease, oil, wax and other foreign matter using a rag soaked in paint thinner.
2. For new Galvanized Iron, wipe clean with paint thinner before sanding surface to enhance paint adhesion. For rusty metal surfaces, wire brush or strip affected areas after applying A-Plus® Rust Converter. Let it sit for 10 – 15 minutes before washing off surface thoroughly with water. Let dry before applying primer.
3. Apply a premium quality metal primer such as A-Plus® Metal Primer or Glazer Galva-Plus® Epoxy Primer immediately upon drying of the surface before rust sets in.

Principal Uses: Interior/Exterior: Wood and Metal Surfaces such as Window Trims, Furniture, Doors, Grills, and many more

Sheen: High-Gloss, Semi-Gloss

Coverage: 25-30 sqm per gallon / coat

Surface Dry: 4-5 hrs

Recoat Interval: 6-8 hrs

Dry Through: 8 hrs Full cure within 3 days at room temperature and 50% relative humidity

Thinning: Maximum 1L A-Plus® PG Enamel Reducer per gallon

Tinting: Can be tinted with A-Plus® Oil Wood Stains at a maximum level of 1/4L per 4L paint to achieve desired shade. Note that Hansa Yellow and Bulletin Red are for interior painting only.

Clean-up Solvent: A-Plus® PG Enamel Reducer

Application: Brush/Roller/Spray

Packaging: 250ml, 1L, 4L, 16L

*Available in 20 factory mixed colors *Also available in Black, White